Most Useful Channelized E1 and Channelized T1 Configuration Commands

Most Useful Channelized E1 and Channelized T1 Configuration Commands

Table of Contents

Channelized E1 and Channelized T1 Setup Commands

autodetect encapsulation
cas-group (controller e1)
cas-group (controller t1)
channel-group
clear controller
clock source (controller)
clock source (Cisco AS5200)
controller
cpp authentication
cpp callback accept
description (controller)
description (interface)
dialer outgoing
dialer voice-call
encapsulation cpp
framing
interface serial
isdn answer1, isdn answer2
isdn caller
isdn calling-number
isdn fast-rollover-delay
isdn incoming-voice data
isdn not-end-to-end
isdn sending-complete
isdn switch-type
linecode
loopback (controller)
loopback local (controller)
loopback local (interface)
loopback remote (controller)
loopback remote (interface)
map-class dialer
pri-group
show controllers e1
show controllers t1
show interfaces serial bchannel
show isdn

 

Channelized E1 and Channelized T1 Configuration Commands

This chapter describes the function and displays the syntax for channelized E1 and channelized T1 setup commands. For more information about defaults and usage guidelines, see the corresponding chapter of the Dial Solutions Command Reference.

autodetect encapsulation

To enable automatic detection of the encapsulation types in operation over a point-to-point link to a specified serial or ISDN interface, use the autodetect encapsulation interface configuration command. To disable automatic, dynamic detection of the encapsulation types in operation on a link, use the no form of this command.

autodetect encapsulation encapsulation-type
no autodetect encapsulation 

encapsulation-type One or both of the encapsulation keywords v120 and ppp.

cas-group (controller e1)

To configure an E1 controller on a Cisco AS5200 with channel associated signaling (also known as robbed bit signaling), use the cas-group controller configuration command. Use the no form of this command to disable channel associated signaling for one or more timeslots.

cas-group channel timeslots range type signal
no cas-group channel timeslots range type signal

channel Single channel group number, in the range 0 to 30.
timeslotsrange One or more ranges of timeslot values, in the range 1 to 31. You can specify timeslot ranges (for example, 1-31), individual timeslots separated by commas (for example 1, 3, 5), or a combination of the two (for example 1-3, 8, 17-31). The 16th timeslot is not specified in the command line, because it is reserved for transmitting the channel signaling.
type signal Specifies the type of channel associated signaling. Choose one of the following signal types to configure:· e&m-fgb–Specifies ear and mouth channel signaling with feature group b support.· e&m-fgd–Specifies ear and mouth channel signaling with feature group d support.· fxs-loopstart— Specifies foreign exchange system loopstart signaling support.

· fxs-groundstart–Specifies foreign exchange system ground start signaling support.

· sas-loopstart–Specifies specific access station loopstart signaling support.

· sas-groundstart–Specifies specific access station ground start signaling support.

cas-group (controller t1)

To configure channelized T1 timeslots with channel associated signaling (also known as robbed bit signaling), which enables a Cisco AS5200 modem to receive and transmit analog calls, use the cas-group controller configuration command. Use the no form of this command to disable channel associated signaling for one or more timeslots.

cas-group channel timeslots range type signal
no cas-group channel timeslots range type signal

channel Single channel group number, in the range 0 to 23.
timeslotsrange One or more ranges of timeslot values, in the range 1 to 24. You can specify timeslot ranges (for example, 1-24), individual timeslots separated by commas (for example 1, 3, 5), or a combination of the two (for example 1-3, 8, 15-23). The 24th timeslot is not specified in the command line, because it is reserved for transmitting the channel signaling.
type signal Type of channel associated signaling. Choose one of the following signal types:· e&m-fgb–Specifies ear and mouth channel signaling with feature group b support.· e&m-fgd–Specifies ear and mouth channel signaling with feature group d support.· fxs-loopstart–Specifies foreign exchange system loopstart signaling support.

· fxs-groundstart–Specifies foreign exchange system ground start signaling support.

· sas-loopstart–Specifies specific access station loopstart signaling support.

· sas-groundstart–Specifies specific access station ground start signaling support.

channel-group

Use the channel-group controller configuration command to define the timeslots that belong to each T1 or E1 circuit.

channel-group number timeslots range [speed {48 | 56 | 64}]

number Channel-group number. When configuring a T1 data line, channel-group numbers can be values from 0 to 23. When configuring an E1 data line, channel-group numbers can be values from 0 to 30.
timeslots range One or more timeslots or ranges of timeslots belonging to the channel group. The first timeslot is numbered 1. For a T1 controller, the timeslot range is from 1 to 24. For an E1 controller, the timeslot range is from 1 to 31.
speed {48 | 56 | 64} (Optional) Line speed (in kilobits per second) of the T1 or E1 link.

clear controller

Use the clear controller EXEC command to reset the T1 or E1 controller.

clear controller {t1 | e1slot/port (Cisco 7200 series and Cisco 7500 series)
clear controller {t1 | e1} number (Cisco 4000 series) 

slot/port Backplane slot number and port number on the interface. See your hardware installation manual for the specific slot and port numbers.
number Network interface module (NIM) number, in the range 0 through 2.

clock source (controller)

Use the clock source controller configuration command to set the E1 line clock source for the Cisco AS5200.

clock source line {primary | secondary}
no clock source line 
{primary secondary}

line E1 line from which the clocking is taken.
primary Primary TDM clock source.
secondary Secondary TDM clock source.

clock source (Cisco AS5200)

To select the clock source for the time-division multiplexing (TDM) bus in a Cisco AS5200 access server, use the clock source interface configuration command. The no form of this command configures the clock source to its default setting.

clock source {line {primary | secondary} | internal}
no clock source line {primary | secondary}

line Clock source on the active line.
primary Primary TDM clock source.
secondary Secondary TDM clock source.
internal Free-running clock (also known as internal clock) as the clock source.

controller

To configure a T1 or E1 controller and enter controller configuration mode, use the controller global configuration command.

controller {t1 | e1} slot/port (on the Cisco 7200 and Cisco 7500 series)
controller {t1 | e1} number (on the Cisco AS5200 and Cisco 4000 series)

t1 T1 controller.
e1 E1 controller.
slot/port Backplane slot number and port number on the interface. See your hardware installation manual for the specific values and slot numbers.
number Network processor module (NPM) number, in the range 0 through 2.

cpp authentication

To enable negotiation of authentication with a router or bridge that supports the Combinet Proprietary Protocol (CPP) and that is calling in to this router, use the cpp authentication interface configuration command. To disable negotiation of CPP authentication, use the no form of this command.

cpp authentication
no cpp authentication

cpp callback accept

To enable the router to accept callback from a Combinet router or bridge that supports the Combinet Proprietary Protocol (CPP), use the cpp callback accept interface configuration command.

cpp callback accept

description (controller)

To add a description to an E1 or T1 controller, use the description controller configuration command. Use the no form of this command to remove the description.

description string
no description

string Comment or a description to help you remember what is attached to the controller.

description (interface)

To add a description to an interface configuration, use the description interface configuration command. Use the no form of this command to remove the description.

description string
no description

string Comment or a description to help you remember what is attached to this interface.

dialer outgoing

To configure the dialer map class for an NSF dialing plan to support outgoing calls, use the dialer outgoing map-class dialer configuration command.

dialer outgoing classname

classname Keyword for a specified AT&T Primary-4ESS NSF dialing plan; the following keywords are supported: sdnmegacomm, and accunet.

dialer voice-call

To configure the dialer map class for an NSF dialing plan to support outgoing voice calls, use the dialer voice-call map-class dialer command.

dialer voice-call

encapsulation cpp

To enable encapsulation for communication with routers or bridges using the Combinet Proprietary Protocol (CPP), use the encapsulation cpp interface configuration command.

encapsulation cpp

framing

Use the framing controller configuration command to select the frame type for the T1 or E1 data line.

framing {sf | esf} (for T1 lines)
framing {crc4 | no-crc4} [australia] (for E1 lines)

sf Specifies Super Frame as the T1 frame type.
esf Specifies Extended Super Frame as the T1 frame type.
crc4 Specifies CRC4 frame as the E1 frame type.
no-crc4 Specifies no CRC4 frame as the E1 frame type.
australia (Optional) Specifies the E1 frame type used in Australia.

interface serial

To specify a serial interface created on a channelized E1 or channelized T1 controller (for ISDN PRI, channel-associated signaling, or robbed-bit signaling), use the interface serial global configuration command.

interface serial slot/port:timeslot  (on the Cisco 7200 and Cisco 7500 series)
interface serial number:timeslot  (on the Cisco AS5200 and Cisco 4000 series)

slot/port Slot number and port number where the channelized E1 or T1 controller is located.
number Channelized E1 or T1 controller number.
timeslots For ISDN, the D channel timeslot, which is :23 channel for channelized T1 and the :15 for channelized E1. PRI timeslots are in the range 0 to 23 for channelized T1 and in the range 0 to 30 for channelized E1.For channel-associated signaling or robbed-bit signaling, the channel group number.The colon (:) is required.On a dual port card, it is possible to run channelized on one port and primary rate on the other port.

isdn answer1, isdn answer2

To have the router verify a called-party number or subaddress number in the incoming setup message for ISDN PRI calls, if the number is delivered by the switch, use the isdn answer1 interface configuration command. To remove the verification request, use the noform of this command.

isdn answer1 [called-party-number][:subaddress]
no isdn answer1 [called-party-number][:subaddress]

isdn answer2 [called-party-number][:subaddress]
no isdn answer2 [called-party-number][:subaddress]

called-party-number (Optional) Telephone number of the called party. At least one value–called-party-number or subaddress–must be specified.
:subaddress (Optional) Subaddress number, 20 or fewer characters long, used for ISDN multipoint connections. At least one value–called-party-number or subaddress–must be specified.Use the colon (:) when you configure both the called party number and the subaddress, or when you configure only the subaddress.

isdn caller

To configure ISDN caller ID screening, use the isdn caller interface configuration command. To disable this feature, use the no form of this command.

isdn caller number
no isdn caller 
number 

number Telephone number for which to screen. Specify an x or X to represent a single “don’t-care” character. The maximum length of each number is 25 characters.

isdn calling-number

To configure an ISDN PRI serial interface to present a billing number of the device making the outgoing call, use the isdn calling-number interface configuration command. To remove a previously configured calling number, use the no form of this command.

isdn calling-number calling-number
no isdn calling number

calling-number Number of the device making the outgoing call; only one entry is allowed and it is limited to 16 digits.

isdn fast-rollover-delay

To specify the time delay between successive attempts to dial out to a number, use the isdn fast-rollover-delay interface configuration command.

isdn fast-rollover-delay seconds 

seconds Number of seconds to delay before dialing the next dialer map after receiving an ISDN message indicating the current call will not succeed.

isdn incoming-voice data

To answer incoming voice calls at a configured rate (overriding the incoming data rate in the call), use the isdn incoming-voice data interface configuration command.

isdn incoming-voice data [56 | 64

56 Answers all voice calls at 56 kbps.
64 Answers all voice calls at 64 kbps.

isdn not-end-to-end

For incoming calls, to override the speed that the network reports it will use to deliver the call data, use the isdn not-end-to-end interface configuration command.

isdn not-end-to-end {56 | 64}

56 Answers all voice calls at 56 kbps.
64 Answers all voice calls at 64 kbps.

isdn sending-complete

To specify that the Sending Complete information element (IE) is included in the outgoing SETUP message, use the isdn sending-complete interface configuration command.

isdn sending-complete

isdn switch-type

To specify the central office switch type on the ISDN interface, use the isdn switch-type global configuration command.

isdn switch-type switch-type 

switch-type Service provider switch type.

linecode

Use the linecode controller configuration command to select the line-code type for the T1 or E1 line.

linecode {ami | b8zs | hdb3} 

ami Specifies alternate mark inversion (AMI) as the line-code type. Valid for T1 or E1 controllers; the default for T1 lines.
b8zs Specifies B8ZS as the line-code type. Valid for T1 controller only.
hdb3 Specifies high-density bipolar 3 (hdb3) as the line-code type. Valid for E1 controller only; the default for E1 lines.

loopback (controller)

To loop an entire E1 line (including all channel-groups defined on the controller) toward the line and back toward the router or access server, use the loopback controller configuration command. To remove the loop, use the no form of this command.

loopback
no loopback 

loopback local (controller)

To loop an entire T1 line (including all channel-groups defined on the controller) toward the line and the router or access server, use the loopback local controller configuration command. To remove the loop, use the no form of this command.

loopback local
no loopback local

loopback local (interface)

To loop a channelized T1 or channelized E1 channel-group, use the loopback local interface configuration command. To remove the loop, use the no form of this command.

loopback local
no loopback local

loopback remote (controller)

To loop packets from a MIP through the CSU/DSU, over a dedicated T1 link, to the remote CSU at the single destination for this T1 link and back, use the loopback remote controller configuration command. To remove the loop, use the no form of this command.

loopback remote
no loopback remote

loopback remote (interface)

To loop packets through a CSU/DSU, over a DS-3 link or a channelized T1 link, to the remote CSU/DSU and back, use the loopback remote interface configuration command. To remove the loop, use the no form of this command.

loopback remote
no loopback remote

map-class dialer

To define a class of shared configuration parameters for outgoing calls from an ISDN interface, use the map-class dialer global configuration command.

map-class dialer classname

classname Unique class identifier.

pri-group

To specify ISDN Primary Rate Interface (PRI) on a channelized T1 or channelized E1 controller, use the pri-group controller configuration command. Use the no form of this command to remove the ISDN PRI configuration.

pri-group [timeslots range]
no pri-group

timeslots range (Optional) Specifies a single range of values from 1 to 23 for channelized T1 and from 1 to 31 for channelized E1.

show controllers e1

Use the show controllers e1 privileged EXEC command to display information about the E1 links supported by the Network Processor Module (NPM) (Cisco 4000) or MultiChannel Interface Processor (MIP) (Cisco 7500 series).

show controllers e1 [slot/port] (on the Cisco 7500 series)
show controller e1 number (on the Cisco 4000 series)

slot/port Backplane slot number and port number on the interface. See your hardware installation manual for the specific slot and port numbers.
number Network processor module (NPM) number, in the range 0 through 2.

show controllers t1

To display information about the T1 links, use the show controllers t1 privileged EXEC command.

show controllers t1 [slot/port] (Cisco 7500 series)
show controller t1 number (Cisco 4000 series)

slot/port Backplane slot number and port number on the interface. See your hardware installation manual for the specific slot and port numbers.
number Network processor module (NPM) number, in the range 0 through 2.

show interfaces serial bchannel

To display information about the physical attributes of the ISDN PRI over channelized E1 or channelized T1 B and D channels, use the show interfaces serial bchannel EXEC command.

show interfaces serial slot/port bchannel channel-number
show interfaces serial number bchannel channel-number 

slot/port Backplane slot number and port number on the interface. See your hardware installation manual for the specific slot and port numbers.
number Network processor module (NPM) number, in the range 0 through 2.
channel-number E1 Channel number in the range 1 to 31 or T1 channel number in the range 1 to 23.

show isdn

To display the information about memory, Layer 2 and Layer 3 timers, and the status of PRI channels, use the show isdn global configuration command.

show isdn {active | history | memory | services | status [dsl | serial number] timers}

active Displays current call information, including called number, the time until the call is disconnected, AOC charging units used during the call, and whether the AOC information is provided during calls or at end of calls.
history Displays historic and current call information, including the called number, the time until the call is disconnected, AOC charging time units used during the call, and whether the AOC information is provided during calls or at the end of calls.
memory Displays memory pool statistics. This keyword is for use by technical development staff only.
services Displays the status of PRI channels.
status [dsl |serial number] Displays the status of all ISDN interfaces or, optionally, a specific digital signal link (DSL) or a specific ISDN PRI interface (created and configured as a serial interface). Values of dsl range 0 to 15.
timers Displays the values of Layer 2 and Layer 3 timers.

Filed Under: Channelized E1/T1

Tags:

About the Author:

RSSComments (0)

Trackback URL

Leave a Reply




If you want a picture to show with your comment, go get a Gravatar.